Channel Liner Install and Removal tool

Ratings Snapshot
4.9
out of 5
5 (8)
4 (1)
3 (0)
2 (0)
1 (0)
Would recommend this product.
100%
Price: $21.95
13ea in stock available for immediate delivery
Code: JCLT
Weight: 0.10pounds
Quantity:

Additional Information

The Glock slide firing pin channel has a part installed in it which is called the channel liner. The channel liner is a tubular shaped plastic part that is pushed into the channel with a special tool and stays in place by way of friction fit. The purpose of the channel liner is to lessen the firing pin spring and spring cup wear and to eliminate the need for lubricant. The liner needs to be removed and replaced with a new one if it gets scored, heavily scratched or when the slide is going to be refinished in an extremely hot environment such as reblueing in a hot tank or when curing finishes in an oven.

Our channel liner tool is designed to both remove and install the channel liner in the Glock slide without damaging the slide.

To remove the channel liner, simply screw the threaded end of the tool into the liner, insert a Glock tool into the hole on the tool and pull the old liner out.

To install a new channel liner, place the liner on the unthreaded end of the tool and push the liner into the channel as far as it will go by hand, then lightly tap the end of the tool with a plastic, wood or brass hammer until it fully seats into the channel.

Ratings & Reviews

9
Ratings Snapshot
4.9
out of 5
5 (8)
4 (1)
3 (0)
2 (0)
1 (0)
Would recommend this product.
100%
4.9
out of 5
5 (8)
4 (1)
3 (0)
2 (0)
1 (0)
Would recommend this product.
100%
9 Total Reviews
Great Tool/Great Service
5 out of 5
wgars433
Location: L. A.
Date: September 11, 2017
The tool is very well made and should work as billed. Haven't had to use it yet, but I have no doubts as to the expected results.
Verified Buyer Recommended
Great tool
5 out of 5
TBEC
Location: Largo, florida
Date: July 30, 2017
Just what is needed for replacing or removing the firing pin sleeve.
Verified Buyer Recommended
channel liner install and removal tool
5 out of 5
Bob
Location: Iowa
Date: July 29, 2017
Needed this tool to finish my slide. Tool worked great. removed old liner and installed new liner in under a minute
Verified Buyer Recommended
Channel liner tool
5 out of 5
Ernie
Location: Phoenix, AZ
Date: July 25, 2017
Works as promised.
Verified Buyer Recommended
Nice tool
5 out of 5
nidgehogg
Location: ma
Date: July 19, 2017
I receved the channel liner tool, looks killer. I will be using it on my new project soon. it's a better looking tool then the one a friend let me use for the last one. 2 Thumbs up..
Verified Buyer Recommended
Excellent tool
5 out of 5
liberal-hater
Location: Michigan
Date: June 18, 2017
Works perfectly, used it to first remove a damaged channel liner and then install a new one.
Verified Buyer Recommended
channel liner remover
5 out of 5
Location:
Date: May 26, 2017
Great tool.
Verified Buyer Recommended
highly recommended
5 out of 5
Coriks
Location: Philippines
Date: April 24, 2017
bought this last month and got it just a couple of days and I already use it in my built and maintenance . a very good tool to have if your Glock diy shooter
Verified Buyer Recommended
Easy to replace with this tool
4 out of 5
mruseless
Location: CO
Date: April 4, 2017
Great little tool. I know you can make due with a lag bolt for removal and a dowel to set the new liner, but I like having the right tool for the job. Not very expensive either. My only addition would be a cross handle rather than having to use your Glock tool for torque and pulling.
Verified Buyer Recommended
9 Total Reviews